Cutting duralight to arbitrary length. We connect the LED duralight with our own hands. Difference from lamp duralight

In recent years, LED strips have almost become equal in popularity LED duralight. This model is now actively used to create decorative lighting. Despite the fact that it has some similarities with the LED strip, there are significant differences in the connection.

LED duralight

Our article will help you figure out how you can connect this cord to the power supply with your own hands and not damage it with inept handling.

Features of the light cord and its types

Duralay is a kind of analogue of an LED strip, in which the diodes are placed inside a polyvinyl chloride cord. It is a silicone shell that provides a high degree of protection of LEDs from moisture and dirt.

Note! To connect LED duralight, know that the circuit here does not require a power supply. This is precisely the main difference from LED strips. A possible connection diagram is shown below.

Connection diagram

Today, LED light cord is often used for street lighting. With the help of duralight they create figures of fairy-tale characters, geometric figures and various advertising inscriptions. You can learn how to make shapes from it in a special video tutorial.
To create a figure, you can use the following types of LED light cords:

duralight chasing. It has multiple LED placement channels. Therefore, when you connect a controller to it, you can create various lighting effects. Duralight chasing is often used for festive or themed lighting;
duralight fisting. Has only one channel. Therefore, it is capable of simultaneous illumination of all its light sources. If you make figures out of it, they can only blink. But for this you need a controller.

Glowing figures

In addition, the LED light cord can be of the following types:

duralight round. It has a circular cross-section. Using round duralight you can make various shapes. It must be remembered that round duralight can sometimes slide off the frame. Therefore, it must be properly attached to the base of the figure;
duralight flat. It is more suitable for creating a luminous figure due to the fact that it can most closely adhere to the frame of the product.

Mark for cutting on duralight

Whatever purpose you use this luminous cable, you need to be able to correctly connect it to a 220 V power supply. But to do this, you need to know specifications lighting product.

Light cord parameters and what you need for installation

The light cable, made on the basis of LEDs, has the following technical characteristics and features:

increased resistance to moisture;
can function in a fairly wide temperature range: from -20 to +50 degrees;
simple installation;
operating from a network voltage of 220 volts;
may have one or more channels (depending on the model).

Note! To connect to the network, it is important to know how many channels the light cable has.

When connected like this LED products you need to know that it, like tape, can be cut into separate pieces. But you need to cut only where the cable is marked accordingly.

In order to install everything yourself, you will need the following materials and tools:

the LED cord itself;
adapters (connectors). They are necessary for fastening the cut sections together;
network cable with a special connector for connection and with a 220 Volt adapter. It should be purchased at the same time as duralight;
protective caps. They are put on the cuts, on the side that does not need to be attached anywhere after cutting the lighting product;
knife and scissors;
fasteners, a screwdriver and a hammer in order to secure the glowing cable in the right place.

After all the materials and tools have been collected, you can begin connecting the duralight yourself.

Step-by-step instruction

It is recommended to connect the LED light cord not to a power outlet, but through a permanent connection. This will avoid the need to call a professional electrician to carry out electrical work.
The adapter plays an important role in the installation process. It is a bridge diode rectifier that converts alternating mains voltage into a pulsating unipolar voltage necessary for the operation of the light cord.

Adapter for duralight

Step-by-step instructions for connecting the LED light cord look like this:

take duralight and cut it according to the marks. Remember that you need to cut only according to such marks, otherwise you will simply ruin an expensive product;

Note! The cutting step is one or two meters!

Cutting duralight

You need to cut the cord with scissors or a sharp knife. When cutting it you need to be very careful. If you make an oblique cut, the product may not work correctly in the future. If you don’t want to take risks, you can buy a ready-made kit with a length of 10 meters and a controller already installed;
The power cord with the adapter must be connected to the duralight using a special adapter, which looks like a metal pin located in the case. The same adapter should be used when it is necessary to connect a piece of light cable together;

Note! This adapter will be different for different models. For a single-row product it will have two pins, for a two-row product it will have three.

Connecting duralight for the network adapter

Now all that remains is to connect all the lighting elements. To do this, insert the plug (adapter) of the power cord into the cable. Moreover, it must be inserted in such a way that the location of the pins coincides with the wires running inside the light cable;
After this, you need to secure the connection using a snap-on lid. It is located in the network cable.

Ready-made duralight that can be connected to the network

Now you can connect the product to the power supply and check its functionality.
After all the lighting elements have been assembled into a single circuit, you need to install a glowing LED cord on the surface. To do this, you need to use transparent special plastic staples.

What

Using different types duralight, the process of connecting them may undergo some changes. But the connection principle itself, described above, will remain without any significant changes.
To ensure that your work is not in vain and you ultimately get the desired result, you must adhere to several recommendations:

Before connecting, you must make sure that the connected product is working;
You need to unwind the cord carefully to avoid possible overheating. Only an unwound product can be connected;
the cut must be made strictly along the line. Due to the fact that the product has a fairly powerful silicone protection in the form of a tube, it is not always possible to make an even and clear cut;
The light tube connection points must be positioned so that they have maximum protection from adverse external influences. This is especially true for mechanical influences;
to increase the tightness of the sections, the cut areas after connection should be additionally treated with silicone sealant or waterproof glue;

Connector and cap for light cord

to avoid the risk of short circuit, this lighting product must be checked for various types of damage to the contacts.

It is also necessary to remember that, despite the high protection, the light cord is, first of all, a rather complex electrical device. In this regard, it must be placed out of reach of pets and small children. Otherwise, there may be a breakdown of the lighting fixture and the risk of electrical injury to children and animals.

Conclusion

Connecting an LED duralight may seem complicated only at first glance. In fact, it is enough to follow simple instructions to create excellent lighting. The main thing when working with this LED cord is to be careful.

Secrets of choosing halogen lamps for the kitchen

A common option today for everyone’s favorite LED strip. The only difference between LED duralight and a conventional LED strip is that the LEDs in duralight are not fixed on a thin strip, but are enclosed in a silicone shell.

Like LED Strip Light, LED duralight itself can also easily be bent at different angles and into different shapes. LED duralight is an excellent lighting solution for beautiful interior design in your home. All you need to add some zest to your interior is to purchase an LED duralight and connect it yourself.

How to connect LED duralight? Yes, very simple! To do this, you just need a special adapter and adapter.

How to connect LED duralight with your own hands

The huge advantage of such lighting is that you can install and connect LED duralight yourself, without outside help or electrical installation skills. You can make a good garland from LED duralight, which will be much more beautiful than a regular factory product.

To connect LED duralight with your own hands, you need to know and prepare this:

have a minimum set of tools. Soldering iron, screwdriver, sharp knife and electrical tape;
it is better to connect the LED duralight to a permanent connection, and not, as many do, through an outlet;

If the light duralight has already been purchased along with a power adapter, then you can safely proceed to its installation and connection.

To connect an LED duralight, you must have a special adapter. It is installed at the end of the power cord, which connects to an outlet or directly to a 220 Volt network. An adapter is built into the power cable itself for connecting the light duralight, which reduces and equalizes the voltage from the 220 Volt network through a diode bridge.

Depending on which LED duralight you purchased (single-row or double-row), you also need an adapter to connect it. For single-row duralight, you need an adapter in the form of two pins, and for double-row duralight, an adapter with three pins installed at the end.

If it is necessary to connect two pieces of illuminated duralight, then an adapter with exactly the same pins is used for this. Be sure to close the opposite end of the light duralight, on which there are exposed wires, with a plastic plug before connecting.

Installation of illuminated duralight to the ceiling surface or to the walls is carried out using special plastic brackets. There is nothing complicated about this.

What you should know when connecting LED duralight with your own hands is that most often it is cut into pieces of one or two meters.

This is done due to the special schematic capabilities of luminous duralight, so it is very important to take this fact into account when decorating the interior of a room with it.

In our online store you can purchase everything you need for a beautiful interior lighting design in your home.

To organize lighting along the contour, secondary lighting, inscriptions and decorations, for the implementation of all of the above, duralight is best suited at the moment. The idea of hiding lighting elements in a transparent tube to protect them from moisture, mechanical damage and for ease of installation is not new, but only with the advent of duralight did it become possible to carry out such installation simply and without excessive effort.

Duralight is an assembly of incandescent lamps or diodes in lines on a flexible board; they are combined into long cords, where each lamp magazine is connected in parallel to a single power bus.

Main technical characteristics:

Degree of protection – IP44;
Operating life – 25,000 hours for incandescent lamps. 100,000 hours for LEDs;
Section - round, rectangular from 5 mm;
Insulation material – PVC;
Resistant to vibrations and ultraviolet radiation;
Power consumption is on average 15-25 W per linear meter.

All duralights are divided into two main types: fixings and chasing.

Fixing is a duralight in which all lamps are powered from a single power bus, and the entire cord has only two power terminals, in which one wire is the neutral, and the second is the power channel itself. Naturally, all elements light up at the same time, and there is no way to control them individually. The only control available is brightness control when using the appropriate controller.

Chasing is a more massive version of duralight, in which even elements of one integral group are connected to one normal and several channels in a certain alternation. Power is supplied through several pins, where one is normal, and all the rest are channels.

Chasing allows you to implement garlands with sequential or random inclusion of elements, organize running lights or other light music. Control is carried out through an appropriate controller capable of covering all duralight channels.

Typically, such light cords are somewhat wider than fixings and, accordingly, require more space in the niches for installation.

There is another notable product on the market - flexible neon, which you can read about. However, unlike duralight, it is not capable of producing light intensity sufficient for illumination, but it glows completely evenly. Flexible neon can only outline the contours of an object, and is clearly visible only in poor lighting conditions or in the dark. Duralight produces a powerful luminous flux, both with and with LEDs, and can play the role of a lighting device. Its glow will be clearly visible both day and night. So when choosing one or another glow cord, it is important to accurately outline the requirements for the product depending on the installation location and the desired effect.

Where is duralight used and how to choose the right one

Thanks to its high IP44 protection, duralight can be used both indoors and outdoors. It is not afraid of moisture and is quite resistant to mechanical stress. The wind will not break or tear. A polymer shell, usually made of PVC, provides it with flexibility and protection along its entire length.

The installation method is extremely simple; the connecting elements include splitters for parallel connection of sections of the glowing cord.

Having such technical characteristics, duralight is perfect for shaping and decorating building facades, illuminating niches, stands, and ceilings. In the interior, it is perfect for illuminating contours in multi-level ceilings, niches in walls, flights of stairs or forming decorative elements. The brightest and most festive way to use it is, of course, to create bright and spectacular garlands on trees, buildings, etc. Especially when it comes to chasing with the ability to control.

Christmas decorations made of duralight

For lighting it is easier to use fixing, it is cheaper and easier to install, and takes up less space. LED duralights, which, unlike incandescent lamps, do not heat up, have become very popular. Read about the benefits of LEDs. In addition, diode duralights can be made in both round and flat versions, which allows different ways install the tape. In the very simple version The duralight power supply is presented in the form of a small adapter designed for power supply from a 220 V network and an output corresponding to the light cord. It is easier to hide than a power supply from diode strips.

It is reasonable to use chasing only where it is really necessary to use it, for example, or change the color of duralight if LEDs are used.

It is worth remembering that tubes with incandescent lamps cannot change their glow color, it depends only on the color of the tube itself; diodes in this regard are much more practical and even look better. The tube used is always transparent, and the color depends on the diodes themselves.

All duralights are equal in degree of protection IP44. Therefore, you can only choose a more reliable one among different manufacturers, counting on the best workmanship. Duralight can be used in a wide temperature range from -40 to +70. Incandescent lamps still react more to temperature changes and heat up on their own, which is why the upper limit is lower in practice.

What is needed to connect duralight

The special beauty of duralight is the ease of its connection and installation. For these products, appropriate fasteners, power supplies, wires, adapters, etc. are already provided. It is best to naturally purchase duralight and all related elements from one manufacturer for full compliance.

In the simplest version, to install duralight you will need:

Construction knife or side cutters;
Duralight;
Power cord with adapter;
Connector, power contacts;
Stub;
Fastenings;
Silicone glue or any other waterproof one.

The light cord is structurally divided only into segments of 1, 2 or 4 meters, but no less. In this it is inferior, for example, to an LED strip, where you can divide a strip into 3-5 elements (2-10 cm). On the duralight itself, the places where they can be separated are marked with a crossbar and a scissors icon.

Controller for connecting duralight

The process of connecting duralight

On a flat, hard surface, the common cord is cut into the required pieces with a knife. In this case, the cut should be smooth and perpendicular to the axis of the cord. There is no need to expose the wires or solder them in the future, but it is desirable that the area be as level as possible.

It is checked that all power bus wires coming out to the end are cut neatly and do not diverge to the sides or become frayed.

The connector is a plastic plate into which metal pins with thinner ends are inserted; they are held in the middle by plastic and stick out in both directions. Usually the plastic has sides or a border of the appropriate diameter for the duralight used. The pins are inserted into the cord all the way so that each contact falls between the veins of each supply wire.

The power cord for duralight already has a corresponding connector, with a mating connector for the pins installed in the cord. There is also a shell, a protective casing that is put on the joint. So all that remains is to connect the power wire and the light cord. It is advisable to additionally protect and glue the junction where the protective casing fits onto the duralight.

Duralight connection

More often, controllers for duralight have their own power adapter unit, and therefore installation is carried out as described above. Otherwise, the controller is inserted between the power adapter and the light cord using connectors.

WITH reverse side The end of the cord remains with bare wires of the power bus. A corresponding plug is put on it, tightly fitting to the cord body. For reliability, again, it is better to use glue for reliability. After this, you can secure the cord in the prepared niche using fasteners. They cover the cord and have an eye for a screw.

Precautionary measures

The duralight is actually powered by a voltage of 220 V. The adapter only converts it from alternating to direct voltage required to power the elements. So the safety precautions are the same as when working with high voltage, this concerns the moment of checking functionality and installation, ensuring the tightness of the connections.

The cord can bend quite strongly, however, the recommended bending radius is 5-6 diameters of the duralight itself. It is prohibited to bend at right angles, as well as to damage the outer sheath, cut or expose part of the wires, or install them in places where they can rub against the enclosing structures. If damaged areas of the shell are found, the corresponding piece from mark to mark is cut out and replaced with a new one.

In contact with

Illumination of buildings and festive decorations have long been carried out using garlands. Recently, most of them are LED. Such lighting is made in the form of ribbons or cords. The LED cord is correctly called duralight; in this article we will look at how it is constructed and connected.

What is duralight, LED features- duralights

The word “duralight” can be literally translated as “durable light” (from the English durable light). And indeed, duralight, upon closer examination, turns out to be a transparent polymer flexible cord, inside of which there are lamps or light-emitting diodes (LED Duralight), essentially a durable tubular garland. The PVC tube acting as a frame provides duralight with moisture resistance, flexibility, UV resistance and physical strength.

A typical LED duralight can operate at ambient temperatures from −50°C to +60°C, and its operating life is only limited - tens of thousands of hours.

Device and types

Duralight is led garland in a polyvinyl chloride shell. It connects to a 220V network; there are several types of it.

By operating mode:

1. Fixing. A cord whose glow remains constant over time. That is, you turn it on, and it just glows.

2. Chasing. This is the name of the operating mode of duralight when it flickers. In order for the LED cord to work in chasing mode, you need to additionally purchase a controller.

3. Chameleon. Essentially the same chasing, but consists of different colors.

There is duralight various types. The number of lines can be from 2 to 7 cores, and the number of LED chains increases accordingly, which allows you to obtain various lighting effects and color combinations.

The shape distinguishes between round and flat LED duralight. The shape determines the ease of installation for a specific lighting configuration.

Since duralight is a PVC cord, it is sealed, which ensures normal operation outdoors.

The duralight cord can be cut; for this purpose there are special marks on its surface either in the form of a strip or in the form of scissors. The cut multiplicity is usually 2 meters.

You can see an approximate diagram in the figure below. The duralight cord consists of conductive cores, LEDs and a sheath. The number of cores and LEDs may vary, as well as their color.

The cord inside is not hollow at all; the spaces between the LEDs are also filled with PVC to give the duralight additional strength. Thus, duralight can be safely used in external and internal advertising structures, in a variety of architectural lighting, for decorating trees and for interior design.

The tube is simply attached to clips or glue wherever needed, and holds securely due to its lightness. The flexibility of PVC allows you to bend the tube at the discretion of the designer, make letters, inscriptions, figures from duralight, or simply distribute the luminous LED tube along the facade of the building. Round and flat duralights, constant glow or with different flashing modes, provide truly the widest possibilities for lighting design.

Single-color and multi-color, flickering and iridescent - modern LED controllers will allow you to realize any design idea.

Pressed into a round tube or flat strip, the LEDs are located at a distance from 1.25 to 27.7 mm, and the power consumption is about 1.5 watts per meter, which is incommensurable with incandescent duralights.

Compared to incandescent lamps, LEDs provide an even, rich color, a bright glow, and almost no heating, which makes LED duralight is much safer than conventional lamp duralight, more economical and more durable.

Connection and installation of LED - duralight

The LED duralight is connected to the network from one end of the cord segment using a special adapter coupling, while the other end is closed with a plug. A conventional bridge rectifier serves as an adapter. It is possible to combine several sections using couplings.

In order to extend the garland cord or connect it in case of repair, pin connectors are used, the connection point is sealed and we will tell you more about this below.

What you need to connect

To turn on the duralight cord, you need to use a special adapter designed for a certain footage. It is a regular rectifier -. The length for connecting the cord depends on its power. The typical length for connection to most adapters is from 50 to 100 meters.

In addition to the adapter, connectors are needed both to connect power to the cord, and to connect several segments or to connect branches. Typical types of connectors are shown below.

In addition, you will need mounting brackets and plugs for duralight. They are shown at the bottom of the previous figure.

Make sure that both the adapter and the connectors are suitable for your duralight, both in shape (flat and round) and in the number of cores, for example, below is a connector from a power adapter for a 5-core cord.

As already mentioned, to connect duralight in flickering mode (chasing) you will need a controller. They differ in the number of channels, respectively, how many channels are in the controller and how many cores can be in duralight that it can power.

Controllers for two-wire duralight provide simple flickering, blinking and smooth switching on followed by switching off the entire garland.

Models for three-core cords already allow the cores to be switched on alternately, thus simulating the effect of rain or the play of colors. The figure below shows that such a controller has three pins in the connector.

You can get a great light show effect by using a five-wire cord with a controller like the one shown below.

Connection diagram

Depending on the number of cores, each of them has a certain connection polarity. Since the duralight garland is powered by rectified pulsating voltage, you need to remember that the polarity of the connection is important - plus and minus.

If you connect the cord and it does not light up, immediately unplug it to avoid damage and turn the connector 180 degrees.

In the figure below you can see the pinouts of 2, 3, 4, 5 and 7 core duralight, both flat and round.

It is advisable to connect pieces of equal power. A special plug is put on the end free from connection. In the manufacture of decorative frame structures, wire or metal tape is used. Special guides will enhance the brightness of duralight.

Installation rules

Before you start working with duralight, read the rules for its installation. Remember that it operates on rectified 220 Volts. This means that at peak the voltage reaches 310 volts!!! Therefore, we have made for you a selection of tips or an algorithm for installing a 220V LED cord.

1. Cut the cord only when it is unplugged - otherwise you may create a short circuit.

2. Make cuts only along specially designated marks, otherwise the cut will not work.

3. Fill the connecting connectors and power connectors with sealant, silicone or glue; you can also additionally protect the joint with heat-shrinkable tubing. This is especially important if the lighting will be used outdoors.

4. Avoid mechanical stress on the connectors; remember that they may become disconnected.

5. Put a cap on the end of the garland - this will save you from defeat electric shock, if you suddenly touch it. Also seal it as described above.

6. It is advisable to place the lighting out of reach of children and animals.

Nuances when working with duralight

A wound coil of duralight cannot be connected to the network for a long time, as this will cause excessive heating. However, before installation begins, the entire cord is checked by connecting it to the network. Contacts must be dry.

You can cut duralight only along the marks, in multiple lengths. Mount - only when switched off, turn on - only after installation is complete. Unused contacts must be protected with plugs. The joints connected by couplings must not be greatly deformed or bent.

The use of heat shrink tubing to improve insulation is encouraged. It is allowed to combine pieces of equal size in terms of power density, designed for the same voltage. Observe polarity!

Ensure normal heat exchange, do not cover the duralight with metal objects. The supply voltage must correspond to the rating voltage for this duralight. Damaged pieces must be removed from the chain. Power supply is rectified voltage only.

Conclusion

The LED cord can be used both indoors and outdoors. This is a convenient solution for lighting or holiday illumination. The advantage of the LED strip is that it operates from a conventional diode bridge, that is, from rectified voltage from a 220V network.

At the same time, there are tips on the Internet that using duralight you can organize lighting for a pool. Of course, if all safety measures are observed, this can be done, but remember - power from high voltage has not gone away, and this is extremely dangerous. For such purposes, a 12V LED strip with dust and moisture protection is ideal.

Duralight is a product of the Chinese company Neo-Neon, which proudly introduced it in 1987. The very name of the product comes from the company that created it. The market reacted sluggishly to its appearance, but a year later its creators had to urgently protect their copyrights to it. Many companies began to produce this product, because many owners of enterprises and organizations retail Bright advertising lighting for stores was needed. Initially, the product used lamps, but soon they began to use LEDs, which significantly expanded their use.

Today, LED duralight is very popular in the field of decorative design in the form of additional lighting in rooms, as well as advertising or festive decoration of shop windows, local areas, trees, building facades and much more. High resistance to various temperature fluctuations (from -40 to +60C), as well as precipitation and unprecedented efficiency make this product indispensable in the field of lighting design.

Kinds

Depending on the shape, duralight can be:

Round - Ø 10 and 13 mm, energy consumption is 18W per 1 m.
Flat - dimensions 5x8 mm, 11x18 mm, 11x22 mm, 11x28 mm, used from 2 to 4 bulbs. This flexible tape is called “duraflex”. It is mainly used to decorate facades.

By type of glow:

Fixing– operates in continuous LED lighting mode. There is only one channel of LEDs or light bulbs inside the cord. When connected, all LEDs (light bulbs) will light up immediately. When using the controller, all LEDs (lamps) will flash at once.
Chasing— operates in various light dynamics modes. It includes 2 or more channels of LEDs (light bulbs), thanks to which you can achieve various effects (changing glow colors, “treadmill”, and so on).
Chameleon- This is a multi-color LED cord.
Multichasing – a cord that implements light scenarios one by one.

The main colors of duralight are white, red, yellow, green and blue. The power consumption mode of each the above options is different, for example, the power of white will be almost twice as strong as blue.

Can also be distinguished by:

Circuit design (the number of cores inside the cord, that is, the number of parallel wires electrical circuit): 5-wire, 3-wire and 2-wire.
Cross-section diameter: 16 mm, 13 mm and 10 mm.
Light bulb color: colored (yellow, red, green, blue) or uncolored.
Brightness: ultra-bright and standard types.
The surface texture of the PVC cord: embossed or smooth.
PVC cord color: multicolor painted, plain painted or transparent unpainted.
The variety can be supplemented with various models: 12V, 220V, USB, indoor, Christmas tree, outdoor and so on.

Device

Duralight is a light cord that has a flexible design. This property allows it to be used in various fields. The cord itself is made of polyvinyl chloride. LEDs are pressed inside it. The LEDs inside the cord are connected in groups. Within a group, they are connected one after another, while the groups are connected in parallel.

This method of placing LEDs is designed to allow the cord to be cut into pieces. In addition, if one LED burns out (break occurs), then the entire group of this LED will stop lighting, while the remaining groups will also light up.

The revolutionary nature of the garland is that the light bulbs and wires are located inside a transparent light-diffusing colored PVC cord. Therefore, the garland is safe, easy to use and maintain, looks beautiful, is very durable and reliable.

Energy consumption depends on the power and placement pitch of the LEDs; usually its value is 2.5 W/rm. A special cord with a plug at the end is placed on the cut edge to connect the power supply. Due to its mechanical contact with the conductors, an electrical connection is created.

For connection, it is advisable to have couplings to ensure convenience and reliable fixation. It is also recommended to take a power cord with a diode bridge. This will allow you to get a rectified voltage without flicker. You can also take an adapter that represents a bridge diode rectifier. He transforms AC voltage into a unipolar pulsating voltage with a frequency of 100 Hz, which is invisible to the eye.

Operating principle

The power cord with the adapter is connected to the duralight through a special adapter. The adapter represents a device from a housing with metal pins. The connector for a single-row garland will consist of two pins, for a two-row garland - three. A similar adapter is used when it is necessary to join 2 pieces (segments) of a garland.

For installation, special transparent plastic brackets are used to secure the garland to the surface. The exposed wires that remain after cutting are covered with a special cap to ensure electrical safety. You need to buy them right away.

It is advisable to connect duralight to a permanent connection, and not to a power outlet. Therefore, it is better to immediately purchase a connector and a power cord with a 220 Volt adapter. Fastening to the prepared surface is carried out using fasteners. When the duralight is plugged into the network, the cord will begin to glow due to the LEDs. The light cord has a flexible design, which allows it to be used to decorate objects of any complexity. With its help, you can create colorful illumination both in the house and outside it.