Why does the iPhone screen turn red. What to do if a red screen appears on the iPhone Red screen on the iPhone 5s

The iPhone red screen often appears after turning on the gadget and displaying a black bitten apple on a white screen. After reddening, the iPhone usually reboots again, and repeats the restart mode many times.

What are the reasons for the red screen of death iPhone 5s and other models?

  • Drops and bumps contribute to the disruption of the connection of the iPhone connectors. Replacing the iPhone 5s cable, or attaching it, will solve the red touchscreen issue in this case.
  • Wetting and moistening the insides of the iPhone, depending on the degree of oxidation, hardware repair any parts of the gadget from a banal power connector to the very heart of the gadget - the iPhone processor can be subject to.
  • Using Chinese counterparts Apple charger. Due to a voltage drop, it may easily be necessary to resolder the u2 (tristar) chip, or maybe replace the iPhone NAND controller.
  • Use of programs of unlicensed origin, or jailbreak. In this case, the problem with the red iPhone display can be solved by a full factory reset, in some cases by flashing the iPhone from backup iTunes or iCloud.
  • It was just unlucky, the iPhone did not fall, did not get wet, and in general is still under warranty. In this case, it is better not to hesitate to take it to an authorized Apple service center, where they will replace the iPhone under warranty.

What errors does the iPhone give when trying to flash it?

  • - which can mean a malfunction of the accelerometer of the compass function, disconnection of the battery connector, a bug with proximity sensors. Also, iPhone error 4013 may be due to the use of a Chinese connector when updating iTunes. Apple developers have reduced the update time to a minimum, so that Chinese cables do not have time to transmit a signal.
  • - shows a non-original Home button, broken button cable home, a bug in the motherboard that cut power to the key house. One way or another, error 53 is directly related to the iPhone Home button, in some cases, restoring the home button loop will help, in others, only replacement under warranty.

By the way, precisely because of the errors that occur when rebooting / flashing iPhones with a red screen, we do not recommend doing this on the advice from the Internet. The fact is that the correct flashing is carried out when a number of connectors are disconnected in order to avoid iPhone errors and bypass the control system. So if your screen iPhone red, then it’s better to bring the handsome apple to us, or we will come for him ourselves. This will save you time searching for answers to the query red screen of death iPhone or iPhone red screen on the Internet, and time is money.

At one point, my iPhone 6 decided to reboot and never turned back on. Instead, it constantly tried to boot, but gave out a "red screen of death". On the Internet they write that this problem can be solved by a normal recovery. Some of you will not be able to cure your smartphone, in which case I advise you to take it to the service, and you will either be replaced or repaired under warranty.

Step 1: Connect iPhone

Open iTunes and connect your iPhone with USB cable.

Step 2: Reset Settings

To reset your iPhone, press and hold the two Sleep/Wake and Home buttons at the same time until you see the Apple logo - DO NOT RELEASE THE BUTTONS.

Step 3: Entering DFU (Recovery) Mode

While holding the Sleep/Wake and Home buttons, wait until the Apple logo disappears. After 3 seconds, release ONLY the Sleep/Wake button (the one on the side) and keep holding the Home button (the round one) until you see iTunes pop up a notification.

Step 4: Restore iPhone

Follow the instructions that appear on the screen. As a result, you will have to click the "Restore" button.

Step 5: Final Restoration

So, now you can either set up your iPhone as new or restore it from the backup button.

ATTENTION! If you've followed all the steps in this article and still haven't fixed the problem, then take your device to a service center.

So tomorrow I'll go to the service to find out what the problem is. Stay tuned!

UPD1: Handed over the smartphone to the service "Your mobile service". They said they would either fix it or replace it within a week and a half.

UPD2: SMS received from the service:

Your iPhone device 6 according to application 10746 dated 11/10/14 is ready for issue from repair.

Called - indeed the phone can be picked up. I came to the service, and they took me out brand new iPhone 6. In general, they replaced my smartphone, and the next day after contacting the service.

Let's take a look at such an error as a red screen on the iPhone 5s and others. iPhone models. This error can be both software and hardware, so we will analyze both. First, let's start with the reasons leading to this error, then we'll see if it's possible to programmatically restore the iPhone, and in the end we'll tell you about the main hardware malfunctions.

The red screen on the iPhone often appears after turning on the gadget and displaying a white bitten apple on a black screen. After reddening, the iPhone usually reboots again, and repeats the restart mode many times.Such a breakdown rarely disappears on its own after rebooting the device - although this is the first thing to do in an attempt to restore the phone.

iPhone 5s red screen what is the reason

The red screen on the iPhone 5S is analogous blue screen Windows death. It indicates that a critical error has occurred on the device.If in Windows reasons If the blue screen of death can be both software and physical, then on the iPhone the red screen of death can be caused by the following factors:

  • Drops and bumps of the iPhone contribute to thedamage to its internal components;
  • Wetting and moistening the insides of the iPhone, depending on the degree of oxidation, any parts of the gadget can be subject to hardware repairs from a banal power connector to the very heart of the gadget - the iPhone processor;
  • Using Chinese analogues of Apple chargers. Due to a voltage drop, it may simply be necessary to resolder the u2 (tristar) chip, or maybe replace the iPhone NAND controller;
  • Failure of the Wi-Fi module;
  • Disconnecting the USB cable from the device during system recovery;
  • Use of programs of unlicensed origin, or jailbreak. In this case, the problem with the red iPhone display can be solved by a full factory reset, in some cases by flashing the iPhone from an iTunes backup, or iCloud;
  • Also, the red screen of death may occur after an unsuccessful update. operating system or pre-installed software.

Programmatic way to solve red screen on iPhone 5s

Method 1. We are trying to do a "Hard Reboot" of the phone. For this we press power buttons and Home for 10 seconds, the iPhone 5s will go into reboot.

Method 2. Before fixing red screen on iPhoneiPhone, install on your computer latest version iTunes programs. Otherwise, during the connection process and iPhone updates the process will crash and the program will give an error. After that, do the following:

  • Connect your mobile device to a computer using a USB cable.
  • To reset iPhone settings simultaneously hold down the Home and Sleep buttons - the apple image should light up on the phone's display - continue to hold the buttons.
  • As soon as the logo image disappears, release the lock screen button (Sleep) while continuing to press Home - iTunes will display a dialog box on the computer screen.
  • Follow the prompts of the program to carry out a full restoration of the device.
  • If you regularly backed up iTunes with iTunes copies of the iPhone, then you can easily restore one of them. Otherwise, set up your smartphone as new, only then you will lose all data on your phone.

Method 3. Restore iOS system without data loss.On the web, you can easily find several programs that offer to restore a failed iOS system without losing data. One of them is Dr.Fone. Do the following steps:

  • Download and install the program on your computer, run it
  • Connect an iPhone with a non-working screen to the computer
  • In the "more tools" menu, select the "iOS System Recovery" option and after the program detects the device, click "Start"
  • Enter the series and model of your iPhone so that the program starts downloading the appropriate software

After this download, which takes from 10 to 20 minutes, Dr.Fone will automatically start updating the smartphone software, and the red screen on the iPhone will be eliminated.

You can also try this ReiBoot program, it is also not bad and can help.

Hardware way to solve red screen on iPhone 5s

The devices are not malfunctioning mainly due to the Loop, Battery, NAND Microchip and Processor. Listed below are the basic solutions to this problem from forms.

  • Most often this problem occurs due to the front camera cable, check by turning on the phone without this cable, if the problem was in it, the phone will turn on and the cable must be changed.
  • Also, the problem may lie in a dead battery, in total it is designed for 500 cycles (according to the Internet), just to check and connect another battery.
  • There was one with a NAND blade, I replaced the power controller and trister, then I pressed the flash and it turned on. I soldered the flash and everything is OK.
  • The soldering c92 and c74 near the eeeprom and further firmware saved me from the red screen.
  • If you use Chinese chargers, then due to unstable voltage, you may need to replace the u2 chip or NAND controller.
  • Some problems on i2c lines can lead to a red screen. For example, the fills are under the backlight driver or the display controller. In general, the first thing to do is to inspect all the components of the i2c0 floor, if everything is in order, then i2c1
  • Such a device came with a red screen, as a result, all the power was replaced, all the voltages were normal, but there was no start, that is, there was a red screen, as a result, it rolled the flash and everything went off, the second same device was on it, there was a replacement of the RAM and a processor reball from the flash .
  • I had a red screen iPhone true when I removed the memory, the processor went into a short circuit, rolled the processor and started up the first time, so one of them.
  • In 90% of such cases, nand is always to blame with nand and you just need to start by throwing another obviously working one, be it from 5, 5s, 5s, 6, 6 plus, if it is flashed successfully, it will hang on activation without a serial, just make an old nanda repair via naviplus or change to a new one.And if on the topic of the red screen, then 90 percent are bad blocks in nanda, it is solved by erasing through the programmer. Rarely have to change, but erasing always helps.If someone says that this is a percent or something else - I make at least 4-5 phones per day with a red return screen 0.
  • I took off the nand yesterday (also a problem with a red display), erased it through ipbox (by the way, it showed very few blocks), soldered it - flashed it.This morning I came to work, already hanging on an apple. With firmware 4013.Part of the operative should fall off, some vulnerable contacts under the process, like in 6ki.It’s also true, but I’ve never met dead nandas at all)
  • Brought here iphone 5s short circuit, according to the client, put the Chinese on the charge, the block exploded changed u2 short circuit passed far removed Nanad erased bad blocks on naviplus everything worked.
  • I talked with the Vietnamese, they said that nandas starting from 4s 64gb (those that are smaller) 1 out of 100 dies, so it doesn’t get sewn up, and newer flash drives from 6ki are even less common.In 99% of cases, a break under the process (in 6k in the corner) contacts AR31 and AP31 - go into the board and are very fragile, and go to nand. Or rolling a sandwich with the restoration of these contacts, or transferring the quartet to another board.This is not true, do not mislead people, although all the specialists are already aware of it. Firstly, these contacts do not go under NAND, but under Eprom, their breakage contributes to error 9 and has nothing to do with error 4013.Quite right, these contacts go to eprom, and from it to memory.
  • When rolling Nanda, the buter just warms up on the other side, so it starts up and works, but it doesn’t last long. In my case, it worked for about two months and returned under warranty. It is necessary to roll the percent.

My iPhone 6 started randomly shutting down last night so I let it charge all night and this morning everything was red. My iPhone is stuck on a red screen. I have read on some forums and they call this red screen of death (RSOD). What causes this iPhone screen problem? It can be fixed? Thanks a lot!

What is the Red Screen of Death (RSOD)?

The red screen of death is a famous nightmare for iPhone users 6. This problem has been spreading all over the internet for quite some time, especially in several forum threads asking for help or solutions on how to fix this iPhone unexpected red error.


When this error occurs, your iPhone screen will turn red and restart after one or five seconds. The process will continue even if the phone itself continues to reboot.

There is another very similar software error that can happen on your iPhone 6. This is the so-called having.

In this case, you will get a blue screen instead of a red screen.

But for possible cause RSOD and BSOD are the same, either due to a faulty software or malfunction of its hardware components. The first thing you can do is call the service Apple service if your phone is still under warranty.

Then you can get a replacement.

Or more,

There are also a few basic steps that you can try to solve the problem yourself.

2. How to Fix iPhone Screen Frozen on Red Screen

You can learn more about how to use FoneLab to fix .

Method 1: Restart your iPhone

You may have already tried it, but if not, it's still worth a try.

Some users have reported that with a simple restart, many issues including iPhone freezing, crashing, not responding, etc. can be fixed. Do the following simple steps, to do this:

Turn off iPhone by pressing and holding power button until you see slide to turn off bar.

And then swipe right.

Wait a minute after the phone turns off completely and then press and hold power button until you see the Apple logo.


For iPhone X/XS/XS Maximum you should follow below tutorial:

Press and hold power button and either Butto volume n until the slider appears.

Press and hold power button


Method 2: Do a hard reset

If a soft restart fails to resolve the issue, try the next step to perform a hard reset.

To do this, press power and home Press at least 10 buttons at the same time until the Apple logo appears on the screen. Release the buttons and let it reboot.

Press and hold power button and either Butto volume n until the slider appears.

Drag the slider to completely turn off iPhone X.

Press and hold power button again until you see the Apple logo.


As you know, iPhone X/XS/XS Max does not have a home button. Can you hard reset your iPhone X?

Of course you can!

Press and quickly release Volume Up Button.

Press and quickly release volume down Button.

Press and hold power button for about 10 seconds until you see the display suddenly turn off.

Retention power button and release when the device reboots.

Method 3. Put iPhone into DFU Mode and Restore with iTunes

This step requires Reserve copy as it will delete your device and all your data and settings will be completely deleted. If you don't have a backup, I won't suggest you take this step to .

However,

You can definitely restore normal iPhone work, restoring DFU mode.

iPad, iPhone 6 and below, iPhone SE and iPod touch:

Connect your iPhone to your computer with a USB cable, then press and hold power and home buttons for seconds 8.

Retention home

iPhone 7 and iPhone 7 Plus:

You must press and hold power buttons and volume down instead of buttons for 8 seconds.

Retention power button until you see nothing on the screen.

iPhone 8, iPhone 8 Plus, and iPhone X and later:

While iPhone 8 and later devices, you need to quickly press and release Volume Up and then volume down button, then press and hold power button until it turns black.

Release after ten seconds power button, but keep holding volume down for 5 seconds.

If your device displays a screen saying that your device is connected to iTunes, which means your device is in recovery mode, repeat these steps.

Users Apple smartphones sometimes encounter their malfunctions. One of these is the red screen on the iPhone 5s. This article will discuss how to fix this problem.

Causes of the malfunction

The red screen on the iPhone (analogous to the blue screen of death on Windows) is a sign of a critical error. Factors causing it:

  • shocks during falls or collisions of the smartphone, as a result of which the integrity of its connectors is violated;
  • contact of the insides of the gadget with water or other liquid, which causes oxidation of parts;
  • use of Chinese chargers, due to which there is a voltage drop;
  • installation of unlicensed or seriously buggy software;

Solutions

In the vast majority of cases, it's a damaged cable that needs to be replaced. To do this, contact service center. This also applies to the situation with the use of a non-original charger.

If the problem occurs after using some application, you need to restore the system through iTunes on the computer. For this:

  1. Install on PC latest version iTunes.
  2. Connect your phone to your computer with a USB cable.
  3. To reset your gadget, press and hold the lock and home buttons.
  4. After the Apple logo appears and disappears, release only the lock button. iTunes will display a dialog box.
  5. Follow the instructions of the program to restore the phone.

If water gets inside the iPhone, do not contact the company center (even if it is under warranty), but immediately go to a regular service center, because Apple warns about such situations and does not provide assistance or replacement parts.

Note! There is a strong possibility that the liquid could brick the phone, because only the iPhone 7 and above are water resistant. Read more about the moisture protection of iPhones in ours.

conclusions

If the screen turns red on the iPhone 5s, you need to determine the cause of the malfunction and contact the service center with an indication of it. If there is a problem due to the software, you need to restore iOS through iTunes on the computer.