Is it possible to change the glass of an iPad? iPad glass replacement cost. Reasons for glass breakage

It's no secret that all Apple products are extremely susceptible to external influences, which is why replacing glass on an iPad 2 is the most common problem with which users contact the service center. Often, replacing the glass on an iPad 2 tablet is required when the device has suffered from external mechanical impact or sudden temperature changes, as a result of which the glass has cracked or the sensor has stopped responding to commands.

The price of replacing glass on an iPad by 2 professionals, including in St. Petersburg, excluding the cost of the glass itself display module fluctuates between 1800 - 2200 rubles. The difficulty is that replacing one glass with iPad 2 is impossible. The presence of a solid display module means that you will have to change both the glass and the touchscreen on the iPad 2. In order to change the glass on the iPad 2, you need to have the appropriate tools at hand, 1 - 2 hours of free time and, of course, patience.

Repair ipad 2 glass replacement: tools:

6-piece set of specialized opening picks;
Thermal bag for heating and softening the glue;
A spudger is a small plastic spatula, one end of which is pointed and the other is flat;
Screwdriver #00.

Replacing glass on iPad 2: operating procedure:

Heat the thermal bag

Place it in the center microwave oven.

You need to make sure that the microwave plate rotates smoothly. If the plate gets stuck, the thermal bag may overheat and burn/melt.

Heat for thirty seconds.
During the repair process, when the thermal bag cools down, it is necessary to reheat it.

Care must be taken to ensure there is no overheating. Overheating can cause the thermal bag to simply melt.

Do not touch the thermal bag if it looks swollen.

If it stays hot in the middle, use it until it cools down. When properly heated, the thermal bag should remain warm for up to 10 minutes.

You should remove the thermal bag from the microwave oven by holding the ends, since the middle of it is very hot. If necessary, use a mitten.

LCD Screen Plate

If the screen glass is cracked, the small pieces must be handled carefully when replacing the display;
Before starting actual work, you need to stick strips of wide tape over the entire iPad display. This will avoid cuts from broken glass and ensure the structural integrity of the glass when lifting the display;
The rest of the manual must be followed strictly. Broken glass will continue to crack as you work, and you may have to use a metal tool to remove it completely.

It is necessary to wear safety glasses to protect your eyes. Also, be careful when handling the LCD screen to avoid damaging it.

Since we are talking about working with small glass fragments that can fly into the eyes, wearing glasses during this manipulation is mandatory!

Place the thermal bag on the right edge of the iPad, in order to maximize contact, apply light pressure;
Leave in this position for 90 seconds and only then try to lift the panel;
There is a small gap in the iPad's adhesive tape on the top right corner of the iPad, about 2.0 inches (~5 cm) from the top of the iPad. It is this gap that must be used;
Insert a spudger under the mute button into the gap between the front glass and the plastic frame. This will be enough to increase the opening;
You may have to apply some force. Work patiently and carefully, and use the plastic spudger only for its intended purpose.
Make sure that the tool is placed in the correct place - between the plastic front panel and the glass of the front panel;
Continuing to hold the spudger in the same place, between the front glass and the plastic frame, insert the pick next to it;
Remove the spudger and slide the pick under the front glass to a depth of ~0.5 inches;
While working to remove the adhesive from the right side area, reheat the thermal bag and place it on the bottom edge of the iPad;
While it heats the bottom edge, continue to work with the sticky layer on the right side of the iPad;
Move the pick up the edge of the iPad to remove the glue;
The adhesive layer is very durable, you may have to apply force, but you must work very carefully;
If the tip of the pick is visible through the front glass, it should be pulled out a little. Such moments should be avoided, since the pick can carry the adhesive onto the front side of the LCD display, which will subsequently be difficult to remove;
You may need to move the heated thermal bag back to the right edge of the iPad. This depends on whether the iPad has cooled down or not;
If the pick gets stuck in the glue, you will have to go back a few millimeters and resume moving along the outer edge of the iPad.
Before removing the pick from the lower corner area, it is necessary to insert a second one under the right edge of the front glass in order to prevent the glue from hardening again;
Warm up the thermal bag again and move it to the top edge of the iPad;
The next few steps require utmost attention;
Wi-Fi antenna attached to bottom right edge rear housing iPad with screws and cable. Due to the location of the Wi-Fi antenna, you must be careful when handling tools, otherwise you may damage it;
You need to remove the adhesive layer between the antenna and the front panel without damaging the thin parts that secure the antenna to the bottom of the iPad;
Now you need to move the pick in the lower right corner of the iPad, thus removing the glue;
Do not move the pick further than the lower right corner, this may damage the Wi-Fi antenna;
You need to move the pick along the lower right edge of the front panel. The Wi-Fi antenna is very close to the corner and is easily separated if you apply too much force to remove the glue;
Do not remove the pick completely from under the front glass, you just need to pull it out slightly so that ~1/8 of it is still under the front glass;
Slide the pick along the bottom edge of the iPad to remove the adhesive layer above the Wi-Fi antenna;
Once the area around the Wi-Fi antenna is completely covered with the pick, you need to reinsert the tool about 3 inches from the right edge or next to the home button to its full depth;
Move the lock, Wi-Fi antenna to the right and thereby remove the glue that secures it to the front glass;
The antenna attaches to the bottom of the iPad using screws and a cable. This manipulation allows you to separate the antenna from the front panel without damaging it;
Continue moving the pick along the bottom of the iPad, pushing the tool deep into the home button area, and then once it is past the home button, insert it again to a depth of 1/2 inch;
If the glue along the bottom of the edge has cooled down, you need to heat the thermal bag again to soften the adhesive layer;
Do not put it in the microwave for more than 30 seconds and make sure that at least 10 minutes pass between heating procedures;
Continue moving the pick along the entire bottom edge of the iPad;
Within iPad models 4, The pick can be inserted to a depth of 1/2 inch in this area to avoid damaging the ribbon cable on the home button;
Insert the pick under the front glass next to the “home” button;
Microwave the hot bag again and place it on the left edge of the iPad to soften the adhesive in that area;
Slide the pick along the top edge of the iPad, pulling it slightly to get around the bracket front camera;
The adhesive layer along this area is very thick and may require considerable effort. It is necessary that the movements be smooth and accurate, make sure that the tool does not slip, otherwise you can do it yourself or the iPad;
If the glue has almost completely cooled down, you need to warm up the thermal bag again and place it along the top edge;
If the pick gets stuck in the adhesive layer, you need to go back and resume movement, as already described;
Continue moving one pick along the top edge of the iPad and move the pick that is in the upper left corner;
If the glue has softened well, you can remove the thermal bag from the iPad to make it easier to work with. However, if the glue is still quite sticky, you will need to reheat the iOpener and place it on the left edge while working;
Slide the pick along the left edge of the iPad, removing the adhesive. The glue here is thin due to the fact that the digitizer runs along the entire left side. Make sure the pick is not too deep (1/2 inch max) to prevent damage to the digitizer;
The digitizer cable is located approximately 2 inches from the bottom of the iPad. Stop the pick movement when the connector reaches ~2.25 inches;
Using the pick that is still on the bottom edge of the iPad, remove the glue from the entire bottom left corner;
The bottom of the digitizer cable is only 1" away from the bottom of the iPad. Make sure to move carefully and slowly to avoid breaking this cable.
Using one of the picks, lift the lower right corner of the iPad and grab it with your fingers;
In some areas around the perimeter of the iPad, the glue may have hardened again. If this is the case, you need to go through the mediator again and “cut” the glue there;
Holding the iPad in the upper and lower right corners, roll the front glass away from the device;
Be careful where the adhesive still sticks to the front panel, you will need to use a pick in these areas;
Remove the four screws using a #00 2mm screwdriver securing the LCD to the aluminum frame;
The front panel ribbon cables are connected under the LCD display. To access them, you need to temporarily flip the LCD display to the opposite side;
You only need to flip the LCD display over, but never try to remove it completely from the iPad. The data acquisition device cable remains connected;
Lift the LCD from its long edge closest to the volume buttons and gently fold it away from the rear case area, as if it were a page in a book;
Place the LCD face down in the front panel area;

Front panel assembly mechanism

Use the flat end of a spudger to gently pry open the retaining flaps on the two ZIF sockets;
Make sure that it is the hinged retaining valves that are captured, and not the sockets themselves;
Use the flat end of a spudger to pry up the digitizer cable latch on the motherboard;
Carefully pull out the digitizer cable, folding it towards the rear case;
Pull the digitizer ribbon cable from two sockets on the motherboard at once;
To remove the entire front panel mechanism, you need to slide out the ribbon cable between the main body and the LCD;
You need to be careful when moving the LCD display, do not try to remove it from the iPad - its cable will still remain connected;
Lift the LCD from its long edge, which is further away from the digitizer cable, and carefully flip it over to the rear case area, the same motion as when closing a book; Hold the LCD display and carefully slide the bezel away from the iPad. You need to be careful not to snag the digitizer cable on the rear case or LCD;
Install the LCD display back into the case;

Replacing iPad 2 touch glass: home button mechanism

The entire “home” button mechanism is fixed on the front panel with glue. The use of a heated iOpener is highly recommended to soften the adhesive layer in this area;
Place the thermal bag in the microwave and heat for 30 seconds at maximum power;
Place it on top of the home button on the front of the display;
Insert the flat end of the spudger under the right edge of the “home” button, now you can understand the right end is up;
Using the same principle, raise the left edge of the “home” button;
Now you can fully raise the “home” button mount on the front panel;
Insert the flat edge of a spudger under the home button mounting bracket;
Move the tool along the bracket holding the springs, thus removing the adhesive layer;
Remove the “home” button bracket from the front panel area;

Replacing broken glass on iPad 2: camera bracket

The camera bracket is attached to the front panel with glue. It is highly recommended to use a thermal bag to soften the glue;
Follow the heating instructions described at the beginning of this manual;
Don't overheat! Wait at least ten minutes before reheating it;
Place it on top of the front camera on the front edge of the top of the display;
Use the flat end of a spudger to remove the adhesive layer between the camera bracket and the front panel;
The camera bracket moves approximately 2 mm to the right/left, depending on the area of pressing;
Raise and remove the camera bracket from the front panel;

iPad 2 glass repair: front panel

Now the front panel remains completely “bare”;
When replacing the panel with a new one, you must remember that the new part may have a protective film on the outside and/or inside the frame. It needs to be removed.

Suitable Products

Found 11 products

100 RUR Buy
100 RUR Buy
500 RUR Buy

Replacement iPad glass 3 – A service that owners of Apple gadgets often need. The problem arises due to big size display, which may be damaged due to careless handling. A broken protective glass on an iPad 3 can lead to a failure of the touchscreen, as well as cause a breakdown of the matrix and other modules of the tablet.

We offer free device diagnostics that will identify any problems. After inspecting and testing the gadget, specialists will be able to qualitatively change the glass on iPad 3. The work performed is provided with a guarantee for a period of 6 months (in some cases it can be extended).

When does the iPad 3 touch glass need to be replaced?

Replacing the iPad 3 touch glass yourself is a big risk. Without professional skills and tools, you can further damage an expensive device. It’s better to immediately contact the Apple “PlanetIPhone” service center. If the iPad 3 glass cannot be repaired, it will need to be replaced. A professional will be able to do the work in your presence. This will take 15-30 minutes.

It is necessary to seek qualified help not only when the glass breaks. Professional services may be needed if:

- The glass cracked as a result of a fall.

- Liquid has entered the housing.

- Due to careless use, scratches appeared.

- The touchscreen began to work incorrectly.

To replace damaged glass, only high-quality, original spare parts are used. After their installation, uninterrupted operation of the device is guaranteed, no different from the operation of a new device.

How much does it cost to replace iPad 3 glass?

Thanks to direct cooperation with component suppliers, the cost of repairing the third iPad will be affordable. The price is lower than in other service centers. The price of professional services directly depends on the complexity of the work. It may be necessary not only to replace the iPad 3 sensor, but also to repair and install other components (power button, camera, back panel, etc.). In this case, Apple repair will take longer. We will tell you the exact deadline for completing the work after a detailed inspection of the device. You can leave your faulty gadget with us and receive it fully functioning in a few days. Delivery services in Moscow are provided free of charge. The courier will deliver the repaired tablet to your home or office.

iPad 3 repair at home.

You don’t have to search for long to find the addresses of service centers in Moscow; you can find them on the website in the Contacts section. The workshops are located within walking distance from metro stations (VDNH, Okhotny Ryad, Taganskaya, etc.). If you do not have the opportunity to go to the service center yourself, the technician is ready to come to you. Replacement of the iPad 3 touchscreen or other damaged components will be performed by a representative of the PlanetiPhone service, efficiently and inexpensively. Our specialists have all the necessary components in stock, so parts are replaced right in front of you.

Apple products are known for their high-quality assembly and excellent device performance. But for various reasons, equipment may require repairs. This often happens due to a person's careless attitude. Replacing the glass on the iPad 2 is required due to damage or other factors. This is discussed in the article.

Reasons for glass breakage

The display usually cracks when the device is dropped. In addition to mechanical stress, glass breaks for the following reasons:

Factory defects. Prolonged use of the device leads to an increase in temperature. If the display is of poor quality and there is air in it, then it will burst when heated.
Use of Chinese components in repairs. Cheap spare parts differ from the originals, so due to various factors they quickly deteriorate.
Battery swelling. Deformation of the battery leads to increased pressure on the glass, causing it to burst.
Hull deformation. Even if the device remains in order after the fall, the condition of the glass continues to deteriorate later. The display may break due to the housing being out of shape.

When is it necessary to change the screen?

Replacing the glass on the "iPad 2" is carried out not only because it broke, but also because of some problems with the touchscreen:

No response to clicks.
Incorrect touch handling.
Part of the touchscreen does not work.
There are cracks.

In case of such problems, device repair is required. After a professional display replacement, the iPad 2 will work properly again.

Diagnostics

Before replacing the glass on the iPad 2, diagnostics are required. The procedure allows you to determine what is broken and why it happened. Moreover, there are not always external signs of a malfunction.

Often the touchscreen module and screen matrix break down with the display. Then it is not only necessary to replace the iPad 2 screen. Modern versions usually require replacing the entire screen module. You should not carry out diagnostics yourself; it is better to entrust this work to professionals.

Difficulties of repair

Replacing glass is considered a complex procedure that requires skills and abilities. During repairs, the following problems may occur:

Torn trains. This is due to improper removal of broken glass, especially when this work is performed by the users themselves.
Unsuitable glue. Glass should not be attached with super glue, as it will break even with minor impacts. And in workshops they use double-sided tape.
Glass cleaning. The old glue must be completely removed, only then will it be possible to install it properly new screen.

The device body may have wrinkled corners. Due to additional defects, the technician’s work becomes more difficult, and therefore the cost of repairs will be more expensive.

Why do you need to contact the service center?

iPad repairs should be performed by a technician. He will make sure that no mistakes are made during work. When working, no dirt or dust should get inside the device. Otherwise, you need to clean and disassemble the tablet again. When ordering work from a professional, a person receives the following advantages:

Quality service.
Use of original spare parts.
Work using professional technology.
Short repair period.
Guarantee.

The iPad 2 device is designed in such a way that repairs are easier than other equipment. But there are a lot of screws in the tablet, so disassembling and assembling requires experience and knowledge, special tool, equipment. All this can only be provided in a professional center.

Price

Masters begin repairing an iPad with diagnostics. After this procedure, you will be able to set a price, since everything depends on the complexity of the work. How much does it cost to replace the glass on an iPad 2? Minimum price is 1500-2500 rubles. It also all depends on the speed of work. If other defects need to be corrected, the price increases.

The repair duration is usually 30-60 minutes. When replacing, the old glass is removed, the body is cleaned of glue and glass, and then the body is repaired. Then, with a constant flow of air, the new display is installed. Special double-sided tape is used for fastening. If everything is done correctly, the new screen will be fixed perfectly.

How to increase the service life of glass?

What needs to be done to make the touch glass work for a long time. Although the device has a scratch-resistant display, it can still crack and break. To extend the life of the iPad 2, you need to treat it with care, that is, protect it from falls, and also avoid excessive loads. Devices are carried in briefcases and cases.

It is important to use a protective film that protects the screen from many adverse factors. Thanks to it, the display will not deteriorate from dirt and scratches. Some films have an anti-reflective effect, thanks to which the tablet can be used in direct sunlight.

Often the screen gets damaged when dropped at an angle. In "iPad 2" the case is made of soft aluminum, so the impact leads to a uniform breakdown of the entire area. To minimize the negative consequences, you need to use covers that cover the case. The device must be protected from falling into water, as liquid leads to the failure of many systems.

Thus, it is better to repair the screen on iPad 2 in a professional workshop, otherwise independent work may worsen the performance of the equipment. And then you will still have to pay to restore the device in a specialized center.

iPad 2 GSM screen and display replacement

Use this guide to replace the screen and iPad display 2 GSM.

Front panel - 14 steps;
Display - 9 steps;
Home button - 3 steps;
Cameras - 3 steps.

Tools:

Hair dryer (preferably with a narrow nozzle);
Mediators for opening;
#00 Phillips screwdriver;
#0 Phillips screwdriver;
Plastic opening tools;
A set of double-sided adhesive tape.

Instructions for replacing the iPad 2 screen - Front panel.

Step 1

If the screen is cracked, cover it with adhesive tape to prevent glass shards from flying around and causing possible injury.

This will prevent the screen from being damaged further when opening it.

Do your best to follow the manual as described. However, if the screen is cracked, it will likely crack as you work, and you may need a metal tool to remove the glass shards.

Wear safety glasses to protect your eyes and be careful not to damage the display.

Step 2

The iPad 2 glass is held in place by adhesive distributed around the perimeter of the screen. To be able to detach the screen, heat each side of the iPad with a hairdryer.

To gain access to the inside of the iPad, there is a gap approximately 5cm wide in the ring of glue along the edges of the screen. It is located under the volume control button.

Insert the tip of the plastic tool into the gap between the front glass and the plastic frame just enough to widen the gap.

This may take some effort, so make sure you warm up this part of the screen with a hairdryer. Be careful and patient when widening the gap between the screen and the gasket, moving the tool up and down.

Step 3

Make sure you place the tool in the correct place - between the plastic frame and the front glass.

Step 4

When the tip of the plastic tool is wedged between the front glass and the plastic frame, insert a pick into the gap in close proximity to the plastic tool. After this, remove the plastic tool from the slot and push the pick deeper under the screen, about 1 cm.

While continuing to heat the edge of the screen, drag the pick along it to release the glue. Be careful, this may require considerable effort. If the pick gets stuck in the glue, rub it in the crack and continue pushing.

If you can see the tip of the pick under the glass, slightly pull it out of the slot. Although you won't break anything this way, some adhesive residue may end up on the display.

When the entire edge of the screen is detached from the case, insert another pick in the middle to prevent the glue from setting again.

Step 5

The next few steps require extreme caution.

The Wi-Fi antenna is attached to the bottom right edge of the iPad's back case using screws and a cable. Due to this position of the Wi-Fi antenna, you must act carefully, otherwise you may cause irreversible damage to it.

You'll have to remove the adhesive that holds the antenna to the front without damaging the thin parts that connect the antenna to the iPad's body. Follow these steps carefully.

Step 6

Place the pick in the lower right corner of the iPad, and with an upward motion, peel the touch glass away from the body.

Warm up this area with a hairdryer.

Pull the pick out from under the glass, but not completely, but so that its tip (about 1/8 of it) remains under the glass.

Slide the tip of the pick along the bottom edge of the iPad, removing the adhesive above the Wi-Fi antenna.

Step 7

After you have passed the Wi-Fi antenna with the pick (in close proximity to the Home button), insert the pick under the glass.

Gently move the tip of the pick to the right, separating the glue holding it in place. Wi-Fi antenna to the glass.

The antenna is attached to iPad case with screws and cable. This step separates the antenna from the front panel, allowing you to remove the glass without damaging the antenna.

Step 8

Continue removing the adhesive along the bottom of the iPad while heating it with a hairdryer. Pull the pick out just enough to avoid hitting the Home button, and reinsert it right after the Home button.

Once the bottom edge of the screen is detached from the case, leave the pick pressed under the front glass near the Home button to prevent the glue from seizing again.

Step 9

Warm up the top edge of the screen with a hairdryer. Slide the pick between the screen and the plastic spacer at the top right corner of the front panel and drag it along the edge, pulling it out slightly next to the front camera.

The glue in this area is very thick and may require a fair amount of force. Be careful and patient to avoid damaging yourself or your iPad.

Step 10

Continue peeling the adhesive along the top edge and drag the tip of the pick around the top left corner.

Step 11

Warm up the left edge of the screen with a hairdryer.

Move the tip of the pick along the left edge of the iPad.

The touchscreen cable is located approximately 5cm from the bottom of the iPad. Do not push the pick below 5.5cm of the left edge.

Step 12

Using a pick that is clamped underneath the bottom of the iPad, release the adhesive along the bottom left corner.

The touchscreen cable is located approximately 2cm from the lower left corner of the iPad. Be careful not to damage it.

Step 13

Using one of the picks, lift the lower right corner of the front panel and grab it with your fingers.

If the adhesive around the perimeter of the iPad has set again, insert a pick into the area where the glass is stuck and cut through the adhesive.

Step 14

Holding the front iPad panel Using the top and bottom right corners, “open” the iPad by unscrewing the glass from the case.

If the glue has set again in some area of the screen, use a mediator.

Instructions for replacing the iPad 2 screen - Display.

Step 15

Remove four 2mm Phillips screws, securing the display.

Step 16

Lift the display from the right side (closest to the volume button) and place it on the front panel, as shown in the second image.

Step 17

Use a plastic tool to carefully remove the two touchscreen cable mounts.

Make sure you are removing the fasteners and not ripping the entire socket off the board.

The fasteners are highlighted in red in the second picture.

Step 18

Use the edge of a plastic tool to disconnect the touchscreen cable from the shields on the board. Carefully remove it from the glue holding it to the body.

Step 19

Remove the touchscreen cable from the two sockets on the board.

Do not try to remove the front panel right away! The touchscreen cable runs under the display. To avoid damaging it, you must first remove the display.

Step 20

Using a plastic tool, remove the display cable retainer that holds it in the socket.

Step 21

Remove the display cable from the socket on the motherboard.

Do not pull the cable up when removing it.

Step 22

Remove the display.

Step 23

Remove the front panel.

Instructions for replacing the iPad 2 screen - Home button.

Step 24

The Home button is attached to the front panel with glue. Use a hair dryer to soften it.

Insert the plastic tool under the right side of the Home button fastener and pull up to release the adhesive.

Step 25

Using the above method, remove the adhesive on the left side of the Home button fastener.

Remove the Home button fastener from the front panel.

Step 26

Insert the edge of the plastic tool under the edges of the Home button.

Move the tool along the button body, removing the adhesive.

Remove the Home button from the front panel.

Instructions for replacing the iPad 2 screen - Camera.

Step 27

The camera is attached to the front panel using glue. Warm it up with a hairdryer to soften the glue.

Use a plastic tool to push the camera bracket away from the adhesive holding it to the front panel.

Be careful not to overheat the camera itself!

The camera bracket needs to be moved about 2mm to the right or left depending on which way you push it.

Step 28

Remove the camera bracket from the front panel.

Step 29

Congratulations, you've captured the screen!

If you are replacing your screen with a new one, be aware that the new screen may have stickers on it. protective film from the outside or inside. It needs to be removed.

To assemble the device, follow the steps in reverse order. Typically, if you buy a new screen for the iPad 2, it either comes with double-sided tape attached around the perimeter, or double-sided tape comes with the tools. You can also use glue, but be careful not to stain the display with it.

When assembling, do not forget that you first need to connect the touchscreen cable, and only then install and connect the display.

When connecting connectors to sockets, be careful to insert the connector exactly into the groove and do not use excessive force - you may damage the connectors.

Fair, not overpriced and not underestimated. There should be prices on the Service website. Necessarily! without asterisks, clear and detailed, where technically possible - as accurate and conclusive as possible.

If spare parts are available, up to 85% of complex repairs can be completed in 1-2 days. Modular repairs require much less time. The website shows the approximate duration of any repair.

Warranty and responsibility

A guarantee must be given for any repairs. Everything is described on the website and in the documents. The guarantee is self-confidence and respect for you. A 3-6 month warranty is good and sufficient. It is needed to check quality and hidden defects that cannot be detected immediately. You see honest and realistic terms (not 3 years), you can be sure that they will help you.

Half the success in Apple repair is the quality and reliability of spare parts, so a good service works directly with suppliers, there are always several reliable channels and your own warehouse with proven spare parts for current models, so you don’t have to waste extra time.

Free diagnostics

This is very important and has already become a rule of good manners for service center. Diagnostics is the most difficult and important part of the repair, but you don't have to pay a penny for it, even if you don't repair the device based on its results.

Service repairs and delivery

Good service values your time, so he offers free shipping. And for the same reason, repairs are carried out only in the workshop of a service center: they can be done correctly and according to technology only in a prepared place.

Convenient schedule

If the Service works for you, and not for itself, then it is always open! absolutely. The schedule should be convenient to fit in before and after work. Good service works on weekends and holidays. We are waiting for you and working on your devices every day: 9:00 - 21:00

The reputation of professionals consists of several points

Company age and experience

Reliable and experienced service has been known for a long time.
If a company has been on the market for many years and has managed to establish itself as an expert, people turn to it, write about it, and recommend it. We know what we are talking about, since 98% of incoming devices in the service center are restored.
Other service centers trust us and refer complex cases to us.

How many masters in areas

If there are always several engineers waiting for you for each type of equipment, you can be sure:
1. there will be no queue (or it will be minimal) - your device will be taken care of right away.
2. you give your Macbook for repair to an expert in the field of Mac repairs. He knows all the secrets of these devices

Technical literacy

If you ask a question, a specialist should answer it as accurately as possible.
So that you can imagine what exactly you need.
They will try to solve the problem. In most cases, from the description you can understand what happened and how to fix the problem.